What Hard Disk For Annke Secuirty Camera?

July ix, 2018.

One of the most crucial components to a security camera organization is the hard bulldoze, the device in which security footage is stored. It allows a user to access recorded video from their security cameras, whether information technology be past accessing a DVR or NVR direct using a monitor or mouse, or accessing the recorder remotely over the internet. There are several practices that every security photographic camera user should keep to ensure their security video recorder is functioning and recording properly.

This post provides a complete guide on how to maintain the security DVR hard bulldoze inside a security camera organization purchased from CCTV Camera World.

• How to install a Difficult Drive inside your DVR or NVR
  • How to install a difficult bulldoze in the NVR044K
  • How to install a difficult drive in the NVR1084K
  • How to install difficult drives in a 2 SATA DVR or NVR
• How to format DVR or NVR hard drive
• Checking Hard Drive Health

How to install a Difficult Drive inside your DVR or NVR

Sometimes it may exist necessary to replace the hard drive inside your surveillance video recorder, or if you don't accept a hard drive and would like to install i yourself, the videos beneath will be helpful. Installing hard drives inside the recorders can be catchy for the novice user. The steps outline for the videos beneath should be followed carefully to ensure you do not damage the difficult drive or the DVR or NVR.

Caution: be certain to take the DVR turned off, and exist on a static gratis surface similar a concrete floor when working on the DVR. Do not use a motorized screwdriver or drill on the unit as information technology may strip the screws on the recorder and crusade incidental damage to the recorder. The recorder'southward limited warranty does not cover user incurred damage.

Step 1: Disconnect your video recorder from ability

The kickoff step in calculation or removing a hard bulldoze in a security camera recorder is to completely power it down and unplug it from the outlet or surge suppressor. This can be done past flipping the switch on the dorsum of the unit of measurement then pulling the cable (past the connector) from the ability port. Once this is complete the user needs to remove the screws from the casing to exist able to remove the top cover from the recorder.

Step two: Disconnect your hard drive(s)

This applies only to scenarios where you are replacing hard drives. In one case inside the unit, the user will be able to see all the inner workings of the DVR/NVR. The difficult bulldoze volition take two cables connected to it: a power cable and a data (SATA) cable. Remove these from the hard drive by pushing down the metal tab on each cablevision and pulling them away from the hard drive. The 2 cables tin can remain connected to the primary lath.

Step three: Remove/Add your difficult bulldoze(s)

You volition demand to remove any screws that are securing it to the mounts inside the recorder. Once this is complete the hard drive will be able to be removed from the main chassis of the recorder. From here it's as elementary as reversing the steps to install the new or additional bulldoze. New hard drives will not need to exist formatted one time they are installed in the DVR. If a used difficult drive is beingness added, it'south a very skilful idea to format the drive. This can be done by navigating through the on-screen menus of the recorder as shown in the side by side section.

How to format DVR or NVR hard drive

Sometimes a format of the hard drive may be needed for your security video recorder. The following video demonstrates how to format the hard bulldoze within your DVR or NVR without having to remove the hard drive from the device.

The outset footstep in formatting a hard drive is to correct-click on the main screen and scrolling down to Main Menu. The user volition then be prompted to log in. Once this is consummate the user must click on Advanced then click on HDD Manage. In roughly the middle of the screen, the user will encounter HDD No., Set, and a button labeled Execute. Using the drop down bill of fare next to HDD No. the user must select which hard drive they want to format. In the Set field, the user must select Format from the drib down menu. Once this is all gear up, the user must hit Execute. A pop-up will then be displayed notifying the user that the DVR/NVR will reboot in order for the changes to take consequence.

Checking hard drive status

From time to time, or when a HDD error is reported, it is a good thought to run a hard bulldoze health cheque every bit demonstrated in the video below.

Matt Rossi is a Technical Support Manager at CCTV Camera World, a leading CCTV Photographic camera distributor located in Buffalo, NY. He is a technical back up expert for everything video surveillance related.

Connect with Matt via: Facebook

Source: https://www.cctvcameraworld.com/managing-dvr-nvr-hard-drive/

Posted by: blackwellcrientic.blogspot.com

Share this post